Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
We have encountered this great article on A Step-by-Step Guide to Installing a Bathtub listed below on the internet and accepted it made good sense to share it with you over here.
Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging task. If the old tub is easily accessible, the project can move easily; if you need to open up a wall surface to remove the old bathtub and also place the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and embeded in the brand-new one. Ensure you have qualified on your own for the job and also are comfortable trying it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to consider employing one before you start. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly assist you set up a new bathtub in your shower room if you have currently gotten a new tub and also do not need to change the setup of your previous supply of water pipelines.
Your tools and also product checklist ought to comprise the following:
Planning for the Installment
Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the restricted accessibility that is often the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this procedure. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Before carrying on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the tub in the needed placement. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub until the level checks out level.
To install taps, fit all-time low of the outermost versatile tap adapter to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub and additionally check the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub should wait up until the tub has actually been made use of a minimum of once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers remain in place in between the faucet and the sink. Protect the tap in place with the maker provided backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The previous type should be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, triggering the water to pass through the wall between the bathroom and the tiling, bring about difficulties with wetness and also possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily offered on the market. It is a good idea to fit the ceramic tiles using water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that editorial about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from someone on another web address. Please take the time to promote this post if you enjoyed it. Thank-you for going through it.
24/7 support? Call. Report this page